Our main products include flexible substrate coating, shielding materials, absorbing materials, precious metal slurries, and more!

banner
Current:Home >Company news >Frontier News >Flexible Soft Magnetic Wave Plate: Selection Logic from Magnetic Loss Principle to Near Field EMI Suppression
先进院(深圳)科技有限公司

Hotline:0755-22277778 Tel:0755-22277778 
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn

Frontier News

Flexible Soft Magnetic Wave Plate: Selection Logic from Magnetic Loss Principle to Near Field EMI Suppression

Time:2026-11-18Number:31

Technical Note  /  Absorber Materials

On an FPC cable between two boards, the peak radiation near 2.4GHz exceeds the limit by several dB. Engineers' first reaction is usually to stick copper foil - after all, "shielding" is the most familiar solution. But the results are often unsatisfactory: the copper foil reflects the noise back into the interior of the body, causing a new peak to emerge at another frequency point; After replacing with a flexible soft magnetic wave plate with a thickness of 0.1mm, the peak at the same position decreased and no new peaks appeared. The improvement brought by such replacement is usually in the order of several dB, depending on the noise source, probe distance, and sheet thickness.

This difference is not related to the strength of the material, but rather lies in their different actions towards noise energy: metals choose to reflect, while absorbing plates choose to absorb. Understanding this boundary is the first step in selection.

01Material: A piece of directionally arranged soft magnetic composite material

A typical flexible soft magnetic wave plate consists of four layers: surface insulation film, magnetic layer, backing adhesive, and release film. The supply form is divided into sheet and roll. What really works is the middle magnetic layer - a composite layer composed of soft magnetic alloy flat powder, polymer matrix (polyurethane, acrylic, rubber or epoxy system) and dispersing, flame retardant and other additives.

The powder system determines the performance ceiling. FeSiAl has balanced corrosion resistance and high-frequency characteristics, and is the main force in the GHz band; Carbonyl iron has high saturation magnetization and large low-frequency μ '; Iron nickel (Pomo) alloy has high magnetic permeability but high cost; Manganese zinc ferrite is cheap and has good low-frequency performance, but it is thick and brittle; Amorphous and nanocrystalline materials are suitable for extreme thinning. The actual formula is often a mixture of several powders, using powders with different resonance frequencies to create a wider loss curve.

There are two most critical actions in the process. firstlyflatteningPress the spherical powder into sheet shaped powders with extremely thin thickness and a large aspect ratio; SecondMagnetic field orientationArrange these flake powders in an orderly manner in the matrix, parallel to the plane of the sheet. The two together produce strong shape anisotropy, pushing the natural resonance frequency of the material to the target frequency band, while allowing the magnetic flux to close inside the sheet and increasing the effective magnetic permeability.

Key points of the projectThe powder is wrapped in resin piece by piece and insulated from each other, so the sheet as a whole is non-conductive, and the surface resistance is usually around 106Ω/□ scale, can be directly attached to bare copper traces or chip surfaces without short circuiting - this is the prerequisite for it to enter FPC and high-density board surfaces.

02Physics: μ 'is responsible for gathering magnetism, while μ' is responsible for consuming noise

The alternating permeability of soft magnetic materials is written in complex form, and the loss factor describes the ratio relationship between the two:

μ = μ′ − jμ″   ·   tanδ = μ″ / μ′

At low frequencies, μ 'has an absolute advantage, making it easy for magnetic flux to pass through; After the frequency increases, the displacement of magnetic domain walls and magnetization rotation cannot keep up with the changes in the external field, resulting in phase lag, a steep decrease in μ 'and an increase in μ' ', forming a peak near the natural resonance frequency, and then falling back.

The noise suppression capability is roughly proportional to the product of μ "and thickness. The higher the thickness of the same thickness, and the thicker the same thickness, the stronger the absorption; But as the thickness increases to a certain extent, the returns decrease, while occupying the stacking space, affecting heat dissipation and flexibility. This explains two parallel trends in the industry: thinning must rely on materials with higher magnetic permeability, while the high-frequency band above 3GHz does not require the "maximum low-frequency μ 'value", but rather a formula with a high resonance frequency and a μ' peak that falls exactly in the target frequency band.

There is another layer that is easy to overlook: if the thickness of the flat powder is controlled below the skin depth of this frequency band, eddy currents are suppressed, and more energy is dissipated in the form of magnetic losses, making it more controllable; If the thickness is too large, the eddy current loss increases, and the material becomes more like a conductor at high frequencies, resulting in reduced absorption performance.

Remember one sentenceAbsorption capacity ≈ ☆× thickness. To catch up with thick sheets, thin sheets can only rely on higher magnetic permeability, not on a darker surface.

03Boundary: It is not a shielding body, nor is it a magnetic separator

dimension Metal shielding (copper foil, shielding cover) Flexible soft magnetic wave plate Magnetic separator (NFC/wireless charging)
mechanism of action Reflection+eddy current cancellation Magnetic loss converted into heat High μ 'magnetic circuit guidance
Is it conductive Conductive, requires grounding Non conductive, can not be grounded Generally non-conductive
Energy direction Reflected elsewhere Scattered within the film Guided around metal
Main battlefield Far field shielding, complete encapsulation Near field (magnetic field dominant region) 100kHz-13.56MHz magnetic coupling
Common failures Cavity resonance, secondary interference Used to reduce efficiency on antennas Almost ineffective for absorbing noise

The three cannot replace each other. Typical misuse is to use magnetic separators to treat IC radiation, with limited improvement; Or use a wave absorbing plate to stick to the antenna clearance area in an attempt to "reduce noise", resulting in a decrease in radiation efficiency. The positioning of the absorption plate is very clear:When the noise has appeared in a place where you don't want it to appear and the space does not allow for shielding or grounding, use a thin piece of material to digest this energy on site.

04key parameters

parameter Industry Common Scope Engineering significance
μ′(3MHz) 50-300, supplied by gear The ability to achieve low-frequency magnetic focusing and thinning is not necessarily better with higher values
total thickness 0.03–0.5mm Determine the absorption amount together with μ 'and match the stacking margin
Applicable frequency band 10MHz – 6GHz (some formulations may reach higher frequencies) Look at the peak position of μ "instead of just looking at the nominal frequency band
surface resistance ≥106Ω/□ Deciding whether to directly attach bare wiring
heat-resistant Conventional -30~85 ℃; Heat resistant -40~125 ℃ Heat resistant type can withstand reflux peak at 260 ℃
flame retardant UL94 V-0 (flame retardant formula) Priority should be given when approaching the battery or the inside of the casing
thermal conduction About 0.5 W/(m · K) High power density areas require assessment of accumulated heat
density 3.6–4.1 g/cm³ Impact on lightweighting and overall weight distribution

Parameters need to be read in groups. High μ 'formula is usually harder, heavier, and attenuates faster in the GHz band; Heat resistant and flame-retardant formulas often have some compromise in magnetic properties. Selecting only the table with the highest single indicator can easily cause the entire machine to overturn.

05Location logic: It's not the material that determines success or failure, it's the distance

The near-field magnetic field strength rapidly decays with distance, so the sheet must be as close as possible to the noise source - the space between the noise source and the absorbing plate, which is where the magnetic flux should be closed the most.

Suggest attaching

  • Above the IC and chip, on the inner wall of the shielding cover (also suppressing multiple reflections in the cavity)
  • Gap between FPC/FPC wiring segments and outlet ports, and between boards
  • Camera module, connector side, inner side of housing gap
  • Inside the shell gap, suppress inward leakage and outward radiation

Should avoid

  • The antenna clearance zone and the area directly above the antenna: a high μ 'will reduce radiation efficiency and shift the resonant frequency
  • Closely attached to power inductor and crystal oscillator: will change the inductance and self resonant frequency
  • Dynamic bending zone: Repeated bending will cause fatigue of the magnetic powder and adhesive layer

Another route is a hybrid structure - a magnetic layer is added with a metal layer of about 1 μ m, and the partially absorbed noise is reflected back to the magnetic layer for secondary absorption by the metal layer, effectively extending the absorption path and making it more effective for high-intensity noise sources. The cost is that the metal layer must be isolated from the circuit by an insulation layer, and attention must be paid to the introduced parasitic capacitance.

06How to verify: Do not use reflection loss as a near-field indicator

The intrinsic parameters of the material are measured using coaxial or waveguide methods to determine the complex magnetic permeability and dielectric constant; The commonly used microstrip line method for board level suppression effect is combined with a ring probe. The vector network analyzer reads S11 and S21, and the power loss is calculated according to the following formula:

Ploss / Pin = 1 − |S11| 2− |S21| 2

During the whole machine stage, the hotspots will be located through near-field scanning, and the remaining capacity will be confirmed through radiation testing.

Common MisconceptionsThe "reflection loss - X dB" on the supplier curve is a far-field indicator, derived from the impedance matching between radar absorption and darkroom scenes, and cannot be directly used to determine the board level near-field EMI suppression capability. When comparing data from different manufacturers horizontally, it is necessary to confirm the testing fixture, line width, sample size, probe height, and whether it includes adhesive layer and insulation film - the numbers cannot be compared due to different conditions.

07Failure modes and process constraints

The more common problems on actual production lines are often not related to electrical performance: sheet warping and edge warping (mismatch between adhesive shrinkage and thermal expansion), die-cutting burrs and magnetic powder detachment, local magnetic circuit discontinuity caused by attached bubbles, decreased surface insulation after wet heat aging, and magnetic performance degradation of ordinary temperature resistance grades after reflow.

The corresponding approach is to select continuous die-cutting of the coil material to stabilize the size, choose with or without glue according to the stacking structure, leave a margin at the height of the component to avoid crushing, and use a low hardness and high elongation formula for surface attachment.

The value of a waveplate is never written in the highest row of the parameter table, but in the matching of frequency, thickness, and position. The same piece of material pasted on top of the IC and next to the antenna yields two completely opposite results - which is why it is worth including in the stacking discussion during the design phase, rather than waiting until the radiation test exceeds the standard for temporary remedies.

For more technical information on flexible soft magnetic absorbing materials, shielding materials, and precious metal pastes, please visitwww.avanzado.cn.

Contact

Contact Us

Company:Xianjin Yuan (Shenzhen) Technology Co., Ltd.

Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China

Tel: 0755-22277778   13826586185

Email:duanlian@xianjinyuan.cn

Related news
Hotline
0755-22277778
13826586185(Mr.Duan)
Wechat QRcode Wechat QRcode