Our main products include flexible substrate coating, shielding materials, absorbing materials, precious metal slurries, and more!

banner
Current:Home >Company news >Frontier News >Breakthrough of the "Snoek Limit" of Soft Magnetic Absorbing Materials: Why Spherical Powder is Not Enough in the GHz Band
先进院(深圳)科技有限公司

Hotline:0755-22277778 Tel:0755-22277778 
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn

Frontier News

Breakthrough of the "Snoek Limit" of Soft Magnetic Absorbing Materials: Why Spherical Powder is Not Enough in the GHz Band

Time:2026-11-17Number:61

In the selection review of soft magnetic absorbing materials, a recurring phenomenon is that the material recommended by the supplier performs well in the low frequency range, but rapidly decays in absorption above 5 GHz. Engineers are forced to increase the thickness to compensate, but the increase in thickness also occupies the already tight space.

The problem is not that the material is' not good enough ', but rather the physical constraint between the material form and the target frequency band - the Snoek limit.

Snoek limit: upper limit of magnetic permeability frequency product of spherical particles

The magnetic loss of soft magnetic materials comes from mechanisms such as magnetic domain wall resonance, natural resonance, and eddy current loss. In the GHz frequency band, natural resonance is the main source of magnetic loss. The natural resonance frequency f_r is directly proportional to the magnetic crystal anisotropy field H_a of the material, while the real part of the magnetic permeability μ 'is inversely proportional to H_a. There exists an upper limit of the product determined by the saturation magnetization strength Ms and the spin ratio γ between the two, known as the Snoek limit:

(μi− 1) fr= (γ / 3π) Ms

The geometric shape of spherical particles is isotropic, and the demagnetization factor is the same in all directions. The magnetic permeability and resonance frequency can only move along this product curve: increasing μ 'and decreasing f_r; Increase f_r and decrease μ '. For materials that require effective magnetic loss above 5 GHz, the available μ 'in spherical form is compressed very low, and the attenuation ability per unit thickness is insufficient, which can only be compensated by increasing the thickness.

That's why spherical FeSiAl and spherical carbonyl iron powder perform well in the low frequency range (several hundred MHz to 2 GHz), but their absorption efficiency significantly decreases in the X-band and Ku band. The situation of ferrite is similar: MnZn is suitable for DC-3 MHz, NiZn can cover 1-300 MHz, and the real part of magnetic permeability rapidly decays after entering the GHz frequency band. The loss mechanism shifts from magnetic loss to dielectric loss and resonance loss.

Path 1: Fragmentation, using geometric anisotropy to "bypass" the Snoek limit

Fragmentation is the most direct engineering method to break through the Snoek limit. The easy magnetization direction of sheet-like particles is arranged along the sheet-like plane, and the in-plane demagnetization factor is much smaller than that in the thickness direction. When sheet-like particles are arranged in parallel in the plane direction, the in-plane magnetic permeability can be maintained at a high level, and the natural resonance frequency will not decrease sharply like spherical particles.

Representative data of sheet-like FeSiAl

Spherical FeSiAl is limited by the Snoek limit, with low magnetic permeability and high dielectric constant, resulting in poor impedance matching; After being ball milled and flattened, the shape anisotropy was optimized, breaking the Snoek limit. The minimum reflection loss reached -49.9 dB at 13.24 GHz, corresponding to a thickness of 1.76 mm, and the effective absorption bandwidth was significantly expanded. The loss ability of sheet-like carbonyl iron powder in the 2-6 GHz frequency band is also significantly higher than that of spherical particles, which is due to the increase in in-plane magnetic permeability and the shortening of eddy current paths caused by the sheet-like morphology.

The engineering cost of flaking lies in the complexity of the process. The preparation of sheet-like powders requires control over ball milling time, medium, and subsequent orientation processes. Batch consistency in fragment size and aspect ratio directly affects the stability of μ 'and loss. The random orientation of flake like powders in the matrix weakens the anisotropy advantage, and it is necessary to align the flake plane parallel to the substrate surface through magnetic field orientation or shear orientation. When the orientation degree is insufficient, the loss of effective μ 'may offset the benefits brought by flaking.

Path 2: Heterogeneous interface construction, supplementing magnetic losses with polarization losses

Fragmentation has increased the frequency band limit of magnetic loss, but a single magnetic loss mechanism still has bandwidth limitations in ultra wide frequency bands. The idea of constructing heterogeneous interfaces is to introduce oxide layers, carbon layers, or MOF derived layers on the surface of magnetic particles, which increase the dielectric losses contributed by interface polarization and dipole polarization in addition to magnetic losses, forming a magnetic dielectric synergistic attenuation.

MIL-101 (Fe) @ Sheet FeSiAl Composite Material

The sheet-like FeSiAl composite with 30 wt% MIL-101 (Fe) after 600 ℃ oxidation has a minimum reflection loss of -71.5 dB at 5.68 GHz, a coating thickness of 3.85 mm, and a significantly increased frequency band width with RL ≤ -20 dB. The improvement in losses comes from two aspects: balancing electromagnetic wave attenuation capability and impedance matching - interface polarization increases dielectric losses, while the oxide layer and MOF shell regulate the dielectric constant, causing the impedance matching window to move in a direction favorable for electromagnetic wave entry.

The engineering boundary of heterogeneous interface paths lies in thickness. A peak absorption of 71.5 dB corresponds to a thickness of 3.85 mm, which is usually unacceptable in space constrained consumer electronics and vehicle modules. Interface engineering is more suitable for scenarios with relatively generous thickness budgets and high requirements for absorption peak and bandwidth, rather than extreme thinning scenarios.

Path 3: Metamaterial structures, replacing material intrinsic limits with macroscopic design

When the inherent Snoek limit of the material cannot meet the bandwidth requirements within the target thickness, metamaterial structures provide a path of "replacing material parameters with geometric design". The introduction of frequency selective surface (FSS) and impedance compensation layer for resistance loading can achieve broadband impedance matching without relying on high μ ', so that the absorption bandwidth is no longer limited by the intrinsic resonance distribution of magnetic materials.

CIP/epoxy based ultra wideband absorber

A representative ultra wideband absorber design adopts a composite structure of CIP/epoxy magnetic substrate, TPU layer, and resistance loaded FSS. Broadband impedance matching is achieved through admittance compensation strategy, achieving absorption of over 90% in the range of 12-49.8 GHz at a thickness of 1.8 mm (0.18 λ ₀), with a relative bandwidth of 122%, and maintaining stable performance under oblique incidence of TE and TM waves. This bandwidth significantly exceeds the level that traditional magnetic materials can achieve at the same thickness. The cost of metamaterial structures is design complexity and frequency band specificity. The unit size and pattern of FSS need to be precisely designed for the target frequency band. Once the frequency band deviates or the structure deforms, the compensation effect may fail. It is more suitable for antenna covers or module level shielding scenarios with clear frequency bands and stable structures, rather than general applications that require broadband compatibility or frequent frequency band changes.

Impedance matching: a common "hidden threshold" for three paths

Whether it is flaking, interface engineering, or metamaterial structures, the realization of absorption performance depends on a common premise: electromagnetic waves can enter the interior of the material rather than being reflected on the surface. The dielectric constant of soft magnetic materials is usually high (especially for sheet-like powders and metal soft magnetic powders). If the dielectric constant is not regulated, the surface impedance of the material will be mismatched with the free space (377 Ω), reflection will be enhanced, and the energy entering the material will be reduced. No matter how strong the magnetic loss mechanism is, it will not be able to play a role.

The engineering methods for impedance matching include: surface coating with a low dielectric layer, gradient packing distribution, and impedance compensation layer in metamaterial structures. When selecting, the input impedance or reflectivity curve of the material in the target frequency band should be confirmed, rather than just looking at the peak of the magnetic loss tangent or μ ".

Selection and judgment of soft magnetic absorbing materials based on "target frequency band x loss mechanism x acceptable thickness"

Firstly, confirm whether the target frequency band exceeds the Snoek boundary of spherical particles

Spherical FeSiAl and carbonyl iron powder exhibit stability below 2 GHz and significant attenuation above 5 GHz. If the target frequency range is in the X-band or above, priority should be given to sheet-like materials or metamaterial structures, rather than using increased thickness to compensate for the shortcomings of spherical materials.

Secondly, match the material system according to the loss mechanism, rather than selecting based on a single "absorption peak"

FeSiAl flakes mainly exhibit magnetic losses and have bandwidth advantages in the frequency range of 8-18 GHz; Ferrite has controllable magnetic losses in the low frequency range, but dielectric losses need to be supplemented above GHz; Rare earth soft magnets (YCoFe, CeFeN systems) have a cutoff frequency of ≥ 8 GHz and an initial permeability of @ 1GHz μ i ≥ 5, making them suitable for scenarios that require both high-frequency magnetic losses and thinning. When selecting, the loss composition of the material in the target frequency band (magnetic loss vs dielectric loss ratio) should be confirmed, rather than just looking at the peak value.

Thirdly, make thickness constraints the first screening criterion, rather than compromising afterwards

The sheet-like FeSiAl reaches -49.9 dB at 1.76 mm, the heterojunction composite material reaches -71.5 dB at 3.85 mm, and the metamaterial structure covers 12-49.8 GHz at 1.8 mm. If the thickness budget for the application scenario is less than 1 mm, priority should be given to evaluating metamaterial structures or high permeability rare earth soft magnetic thin films, rather than searching for "thinner versions" in thick materials.

Fourth, confirm impedance matching data, not just loss data

Require suppliers to provide reflectance curves or input impedance data for the target frequency band to confirm whether the material is in an "absorption dominant" rather than a "reflection dominant" state in the target frequency band. The dielectric constant of flake powder and metal soft magnetic powder is relatively high. If the supplier does not provide instructions for regulating the dielectric constant, the risk of impedance mismatch needs to be independently verified.

Advanced Institute (Shenzhen) Technology Co., LtdThe product line of soft magnetic absorbing materials covers sheet-like FeSiAl, carbonyl iron powder composite systems, and rare earth soft magnetic thin films. It can provide reflection loss curves, loss mechanism decomposition, and impedance matching evaluation data for the target frequency band (1-40 GHz), supporting the matching of material morphology (spherical/sheet-like) with the matrix system based on thickness constraints and frequency band requirements.

For more technical information, please visithttp://www.avanzado.cn/.

Contact Us

Company: Xianjin Yuan (Shenzhen) Technology Co., Ltd.
Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China
Tel: 0755-22277778  |  13826586185
Email: duanlian@xianjinyuan.cn
Website: http://www.avanzado.cn/
Related news
Hotline
0755-22277778
13826586185(Mr.Duan)
Wechat QRcode Wechat QRcode