The verification of RFID samples using magnetic sheets is usually completed under an "ideal alignment" condition: the center of the sheet is aligned with the center of the tag antenna, the edge margin is uniform, and the mounting is flat. The read distance recovery rate and resonance offset measured under these conditions are considered as performance indicators of the sheet material.
It is difficult to reproduce this' ideal alignment 'during mass production and assembly. The die-cutting part is removed from the reel, passed through the mounting machine, and pressed onto the back of the antenna. There is a deviation of a few tenths of a millimeter to one millimeter in the relative position between the sheet and the antenna. When manually mounted, the offset is greater. When the curved surface is adhered, the sheet may slip during the pressing process. These offsets were not covered in the sample validation, but they actually existed in mass production. After the offset exceeds a certain threshold, the reading distance may decrease by one level - from "stable reading" to "intermittent reading", or from "long-distance reading" to "only close range reading".
The edge of the sheet is a magnetic permeability discontinuity boundary, and the offset changes the symmetry of the magnetic flux
In the plane of the magnetic sheet, the magnetic permeability is uniform; Beyond the edge of the sheet, the magnetic permeability drops sharply to near air. This boundary is the "turning point" of the magnetic flux path: magnetic field lines propagate along a high permeability path inside the sheet and need to "turn" back to the antenna or enter the surrounding space at the edge.
Differences in magnetic flux paths between center alignment and offset
Center alignment:When the sheet is aligned with the center of the antenna, the magnetic flux paths on both sides of the antenna are symmetrical: the magnetic field lines on the left side turn through the left edge of the sheet, and the ones on the right side turn through the right edge. The length and magnetic resistance of the paths on both sides are roughly equal. The equivalent inductance of an antenna is the result of symmetrical loading.
After offset:The sheet is offset to one side, and the edge of that side is closer to the antenna, resulting in a shorter path for the magnetic field lines to 'turn'; The edge on the opposite side is further away from the antenna, and the magnetic field lines need to take a longer path to 'wrap back'. The magnetic resistance on both sides is no longer equal, and the magnetic flux distribution is concentrated towards the side with lower magnetic resistance.
This asymmetric magnetic flux distribution is equivalent to the uneven loading of the medium around the antenna. The equivalent inductance of an antenna is no longer a single value, but a distribution of "one side higher and the other side lower in the offset direction". The offset of the resonant frequency is no longer the same value as when the center is aligned.
Offset, sheet size, and antenna size: coupling of three variables
The degree of influence of offset is not determined solely by the offset, but by the ratio of offset to the sheet size and antenna size.
Offset/Sheet Size
The larger the sheet size, the smaller the "relative displacement" of the same offset on the sheet scale, and the less obvious the unevenness of the edge margin. A 30mm x 30mm sheet is offset by 0.5mm, with a relative displacement of approximately 1.7%; A 10mm x 10mm sheet is offset by 0.5mm, with a relative displacement of approximately 5%. The latter has a more significant impact on the symmetry of magnetic flux.
Offset/antenna size
The smaller the antenna size, the narrower the spatial range of the antenna near-field, and the more direct the disturbance of the near-field distribution caused by the sheet offset. Small size antennas (such as NFC tag antennas, typically 10-20 mm in size) are more sensitive to sheet offset than large-sized antennas.
Margin of sheet size/antenna size
The larger the margin of the edge of the sheet relative to the antenna, the wider the offset "fault-tolerant window". If the margin on each side of the sheet is only 0.5 mm, a deviation of 0.5 mm is sufficient to zero the margin on one side, and the magnetic flux path on that side is' cut off '. If there is a margin of 2 mm on each side and there is still a margin of 1.5 mm after offsetting by 0.5 mm, the continuity of the magnetic flux path can be maintained.
The coupling of these three variables explains a common phenomenon: the same sheet is sensitive to offset when used on small antennas, but insensitive to offset when used on large antennas; Items with wider edge margins on the same sheet have a higher tolerance for mounting offset.
The direction of offset also has an impact: lateral offset is not equivalent to longitudinal offset
For long strip tag antennas (such as UHF dipoles), the effects of lateral offset (along the short axis direction) and longitudinal offset (along the long axis direction) of the sheet on performance are not equivalent.
The difference in the influence of two offset directions
Vertical offset:The change is the length of the magnetic flux path at both ends of the antenna's long axis, which has a relatively mild impact on the resonant frequency.
Lateral offset:The change is the magnetic flux symmetry on both sides of the antenna, which has a more direct impact on the resonant frequency and input impedance.
For circular or square NFC antennas, the offset effects in both directions are relatively close, but the relative relationship between the offset direction and the antenna feed point still affects matching.
This means that 'offset tolerance' is not an isotropic number. When selecting, the offset tolerance of the sheet in the critical direction (usually the direction with the greatest impact) should be confirmed, rather than assuming that "all directions are the same".
Selection and installation judgment based on "offset tolerance x sheet size x antenna size"
Firstly, introduce "offset testing" during the sample stage, rather than just measuring center alignment
Offset the sheet relative to the antenna by ± 0.3 mm, ± 0.5 mm, and ± 1.0 mm, and measure the resonant frequency and reading distance at each offset position. Draw the "offset reading distance" curve and confirm at which offset the reading distance begins to decrease significantly. This curve is more predictive of mass production performance than a single data point when the center is aligned.
Secondly, select the sheet size according to the antenna size and reserve sufficient "offset tolerance margin"
The margin on each side of the sheet should be greater than the expected maximum mounting offset plus the minimum margin required for magnetic flux bypass (usually 1.0-1.5 mm). If the expected offset is 0.5 mm, the margin on each side should be at least 1.5-2.0 mm. When the margin is insufficient, the offset will directly "eat up" the turning space of the magnetic flux path.
Thirdly, control the offset in the mounting process and incorporate "alignment accuracy" into the process specifications
If using an automated mounting machine, confirm whether the mounting accuracy of the equipment meets the offset tolerance requirements of the sheets; If manual installation is used, add alignment assistance (such as silk screen marking, positioning fixtures) to reduce manual deviation. For surface fitting, consider using pre formed sheets or segmented mounting to reduce slippage during the pressing process.
Fourth, prioritize ensuring alignment accuracy in key directions rather than pursuing "isotropic uniformity"
For long strip antennas, the impact of lateral offset is usually greater than that of longitudinal offset, and lateral alignment should be prioritized during installation. For circular antennas, the relative relationship between the offset direction and the feeding point is more important, and during installation, it should be confirmed whether the offset direction falls in the "sensitive direction".
Advanced Institute (Shenzhen) Technology Co., LtdThe RFID magnetic sheet product line covers ferrite composite sheets and nanocrystalline composite sheets, providing resonance frequency offset and read distance reduction data at different offsets, as well as suggestions for matching sheet size and margin according to antenna size and expected mounting offset.
The product supports customized die-cutting profiles based on the shape and feeding structure of the tag antenna, helping engineers extend the "center alignment verification" to "available offset tolerance". For more technical information, please visithttp://www.avanzado.cn/.


