Our main products include flexible substrate coating, shielding materials, absorbing materials, precious metal slurries, and more!

banner
Current:Home >Company news >Frontier News >The 'tolerance chain' of magnetic sheets used in RFID: why do sheets of the same model match well on project A, but need to be re tuned when switching to project B
先进院(深圳)科技有限公司

Hotline:0755-22277778 Tel:0755-22277778 
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn

Frontier News

The 'tolerance chain' of magnetic sheets used in RFID: why do sheets of the same model match well on project A, but need to be re tuned when switching to project B

Time:2026-11-16Number:14

In the selection review of magnetic sheets for RFID, engineers usually confirm a number: what is the μ 'at 13.56 MHz. μ′ 150、μ′ 130、μ′ 100, These nominal values seem sufficient to answer the question of whether the sheet can be used.

But a common phenomenon in mass production is that the same type of sheet material can be used simply by sticking it on Project A, and the matching capacitor does not need to be adjusted much; Switching to Project B, with the same sheet material and tag antenna design, the resonant frequency is biased and the reading distance cannot meet expectations. The production line needs to readjust the matching parameters. The difference may not necessarily come from 'wrong material selection', but from 'where the tolerance zone falls'. The nominal μ 'is the same, but the actual delivered sheets may fall on the upper and lower edges of the tolerance zone, while the antenna matching margins of the two projects are different, resulting in different tolerances for the same tolerance zone.

μ 'is not a' number ', it is a tolerance zone

The μ 'of magnetic sheets is a nominal value on the specification sheet and a distribution in mass production delivery. The specification of YS/T 1417-2021 for nickel zinc ferrite composite foil at 13.56 MHz is a real part magnetic permeability of 130 ± 26, with a tolerance band of approximately ± 20%. T/ZZB 1579-2020 also requires a real part tolerance of ± 20% for the complex magnetic permeability of sintered ferrite sheets. Some suppliers have optimized batch fluctuations to within ± 10%, while the consistency data for mass production batches at Advanced Institute Technology is ± 8%.

The significance of tolerance zone width for matching networks

The difference between ± 20% and ± 8% is not just a narrative with higher accuracy. For the 13.56 MHz NFC antenna, the adjustable range of the matching network is limited. If the μ 'of the sheet material falls on the upper edge of the tolerance band, the amplitude of the antenna inductance being pushed higher will be greater, and the resonant frequency will shift more towards lower frequencies; If it falls on the lower edge, the inductance loading is weak, but the anti metal magnetic flux guidance ability also decreases accordingly. The matching network needs to be able to pull the resonance point back into the chip's tolerance window within the entire tolerance band - if the matching margin itself is not sufficient, the upper or lower edge of the tolerance band will become the boundary between "some batches can be used and some batches cannot".

The superposition of thickness tolerance and μ 'tolerance: the product of two tolerance chains

The tolerance chain of magnetic sheets is more than one μ '. The thickness tolerance also participates in the formation of inductance loading and magnetic flux capacity. The typical thickness tolerance range for sintered ferrite sheets is ± 0.005- ± 0.014 mm; the thickness tolerance for magnetic separators from Advanced Institute Technology is marked as ± 0.01 mm.

The influence direction of two tolerances on inductance is superimposed

The influence direction of thickness tolerance and μ 'tolerance on antenna inductance is superimposed. A sheet with a thickness of μ 'falling on the upper edge has the strongest inductance loading effect and the largest resonance offset; A sheet with μ 'falling on the lower edge and thickness also falling on the lower edge has the weakest loading effect. If the supplier's μ 'tolerance and thickness tolerance are independently controlled, the worst-case superposition offset may be significantly greater than expected for a single tolerance zone.

More importantly, the μ 'tolerance and thickness tolerance are not simply an additive relationship in the magnetic circuit. The increase in thickness simultaneously increases the magnetic flux capacity (beneficial for metal resistance) and inductance loading (requiring matching compensation), and the direction of increase in μ 'is consistent with the direction of increase in thickness in driving the resonant frequency. The tolerance bands of the two are superimposed under the "most unfavorable combination", making the distribution range of resonance offset wider than implied by the tolerance band of a single parameter.

Why do "high μ 'batches" and "low μ' batches" perform differently on the same project

Assuming an NFC tag antenna is tuned to 13.56 MHz in free space and a magnetic sheet with a nominal μ'150 is attached, the resonant frequency shifts to 13.2 MHz. The design of the matching network is to pull back the 2.2 MHz offset.

batch Actual μ ' Resonance offset Performance after matching compensation
μ 'falls on the upper edge About 180 2.6–2.8 MHz The resonance point may still be around 13.56 MHz after being pulled back, but the Q value and bandwidth may have deviated from the design expectations
μ 'falls at the center value About 150 2.2 MHz Match the compensation amount with the offset amount, and both the resonance point and Q value are within the expected design range
μ 'falls on the lower edge About 120 1.6–1.8 MHz The matching network is pulled too far, and the resonance point is pushed above 13.56 MHz, which is also detuned

In projects with ample matching margin, both of these situations may be absorbed; On projects with tight matching margins, the upper and lower batches may exhibit "low efficiency" and "insufficient reading distance", respectively. The nominal μ 'of the sheet has not changed, what has changed is the ability of the project matching network to digest the tolerance zone.

Selection judgment based on "tolerance zone x matching allowance"

Firstly, use the width of the μ 'tolerance zone as a selection parameter to confirm, rather than just confirming the nominal value

Require suppliers to provide tolerance ranges (such as ± 20%, ± 10%, ± 8%) and batch distribution data for μ 'at 13.56 MHz, rather than just' typical value of 150 '. ± 20% and ± 8% mean completely different mass production risks for projects with tight matching margins.

Secondly, confirm the joint distribution of thickness tolerance and μ 'tolerance, rather than looking at two isolated tolerance zones separately

If the supplier can only provide separate ranges of μ 'tolerance and thickness tolerance, but cannot provide inductance offset data under the joint distribution or worst-case combination of the two, the superposition effect of the tolerance chain cannot be predicted. Suppliers can be requested to provide patch resonance data for two boundary samples: "upper edge thickness upper edge" and "lower edge thickness lower edge", to verify whether the matching network covers the entire tolerance zone.

Thirdly, use the matching tolerance of the project as the basis for selecting supplier tolerance levels, rather than the other way around

If the matching network of the tag antenna has a large adjustable range, a tolerance band of ± 20% can be absorbed, and a cost-effective standard product is a reasonable starting point; If the matching tolerance is tight, it is necessary to choose sheets with a tolerance band of ± 10% or narrower, or reserve a larger compensation margin during the antenna design phase. The selection of tolerance level should be determined by the matching margin of the project, rather than by "which one is cheaper".

Fourth, use "tolerance zone boundary samples" for verification during the sample stage, rather than just using center value samples

The passing of the center value sample does not mean that batches with upper and lower edges of the tolerance zone can also pass. Request the supplier to provide samples of the upper and lower edges of the μ 'close tolerance band, which should be attached to the actual tag antenna to measure the resonant frequency and reading distance. If one direction does not pass through the boundary sample, the matching network needs to be redesigned or the tolerance zone needs to be narrowed.

Advanced Institute (Shenzhen) Technology Co., LtdThe RFID magnetic sheet product line covers ferrite composite sheets and nanocrystalline composite sheets, providing a tolerance band width of μ 'at 13.56 MHz (consistent with production batches ± 8%), thickness tolerance (± 0.01 mm), and patch resonance offset evaluation data under the joint boundary conditions of μ' and thickness.

The product helps engineers extend the selection criteria from "nominal μ '" to "matching of tolerance chain and matching allowance". For more technical information, please visithttp://www.avanzado.cn/.

Contact Us

Company: Xianjin Yuan (Shenzhen) Technology Co., Ltd.
Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China
Tel: 0755-22277778  |  13826586185
Email: duanlian@xianjinyuan.cn
Website: http://www.avanzado.cn/
Related news
Hotline
0755-22277778
13826586185(Mr.Duan)
Wechat QRcode Wechat QRcode