Our main products include flexible substrate coating, shielding materials, absorbing materials, precious metal slurries, and more!

banner
Current:Home >Company news >Frontier News >Is there a solution to the "filling rate paradox" of flexible soft magnetic wave plates: if you want them to be flexible, you need less filler, and if there is less filler, there will be no absorption
先进院(深圳)科技有限公司

Hotline:0755-22277778 Tel:0755-22277778 
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn

Frontier News

Is there a solution to the "filling rate paradox" of flexible soft magnetic wave plates: if you want them to be flexible, you need less filler, and if there is less filler, there will be no absorption

Time:2026-11-18Number:32

In the selection review of flexible soft magnetic wave plates, engineers usually see two sets of parameters: one is magnetic performance - magnetic permeability, magnetic loss tangent, and reflection loss; The other group is mechanical performance - flexibility, bending radius, and bending resistance. The two sets of parameters are presented side by side on the specification sheet, and it appears that they can be optimized independently.

But at the material structure level, these two sets of parameters are bound by the same variable: the filling rate of the magnetic filler. High filler content, multiple sources of magnetic loss per unit volume, high magnetic permeability and loss, and good absorption performance; However, at high filling rates, the continuous phase of the polymer matrix is "cut off" by the filler particles, resulting in a decrease in the flexibility and ductility of the sheet, making it more prone to cracking during bending. The filler content is low, the polymer continuous phase is intact, the sheet is soft and bendable, but the magnetic particles are sparse, the magnetic coupling path is discontinuous, and the magnetic loss ability is insufficient. This is not a contradiction that can be completely eliminated by "choosing better fillers" or "changing to a better matrix". It is a structural feature of flexible composite absorbing materials.

Seepage threshold: the location where magnetic performance jumps and flexibility brittleness occur simultaneously

For particle filled composite materials, there exists a critical filling rate - the percolation threshold. When it is below the threshold, the particles are separated by the polymer matrix, and the magnetic coupling and conductive path between particles are intermittent. The effective magnetic permeability and loss slowly increase with the increase of filling rate. When approaching the threshold, a continuous overlapping network is formed between particles, and the magnetic coupling path and the conductive path suddenly connect, resulting in a significant increase in effective magnetic permeability and loss.

Simultaneous occurrence of magnetic property leap and flexibility brittleness

For flexible wave absorbing plates, this leap is accompanied by another change: the continuity of the polymer matrix is disrupted. At high filling rates, filler particles occupy the majority of the volume, and polymers can only form thin layers in the gaps between particles. The deformation ability of the sheet changes from "matrix dominated" to "particle overlap network dominated". The particle overlap network is subjected to relative slip between particles and point contact shear during bending, rather than elastic deformation of the polymer. The result is that while magnetic properties increase, flexibility decreases and brittleness increases.

There are studies showing that in the NiZn ferrite/YSZ composite system, the magnetic permeability threshold is about 0.6 volume fraction of ferrite; The same set of data shows that the Vickers hardness of composite materials begins to 'significantly decrease' when the ferrite content exceeds 0.5. The leap in magnetic properties and the embrittlement of mechanical properties are located close to but opposite in direction on the filling rate axis - this is the most important interval to be quantified in the selection of flexible soft magnetic wave plates.

Sheet shaped filler: elongating the magnetic coupling path with a length to diameter ratio to reduce dependence on filling rate

The first path to alleviate the paradox of filling rate is to change the geometric shape of the filler - from spherical particles to sheet-like particles.

The mechanism and cost of sheet-like fillers

The aspect ratio of sheet-like fillers is much larger than that of spherical particles. At the same filling rate, the overlap probability between sheet-like particles is higher, making it easier to form a continuous magnetic coupling network. This means that to achieve the same effective magnetic permeability or loss level, the filling rate required for sheet-like fillers is lower than that for spherical fillers. As the filling rate decreases, the continuity of the polymer matrix is preserved and the flexibility is correspondingly improved.

The application of sheet-like FeSiAl in flexible absorbing wave plates is a manifestation of this logic: the shape anisotropy brought by the sheet-like morphology enables the material to achieve usable magnetic loss at lower filling rates, while the bending durability of the sheet is better than that of spherical filler schemes with equivalent magnetic properties. The cost is that the preparation process of flake powder is more complex, the batch consistency of fragment size and diameter thickness ratio needs to be controlled, and the orientation of flake particles in the matrix also affects the final performance - random orientation will weaken the anisotropy advantage.

Double peak particle size grading: using small particles to fill in the gaps and improve flowability at the same filling rate

The second path is particle size grading. Single particle size fillers have a high porosity between particles; If fine particles are filled between coarse particles and the gaps between coarse particles are filled with fine particles, the overall packing density increases, and the contact probability between particles increases at the same filling rate, resulting in a more continuous magnetic coupling network.

The engineering benefits of bimodal grading are: a decrease in the filling rate required to achieve the same magnetic properties, or a slight improvement in both magnetic properties and flexibility at the same filling rate. The addition of fine particles also improves the flowability of the composite system during the molding process, reduces local filler enrichment and voids, and enhances the uniformity of the sheet. The boundary of bimodal gradation lies in the particle size ratio. The particle size ratio of coarse particles to fine particles is too small, and fine particles cannot effectively fill the gaps; If the particle size ratio is too large, the specific surface area of fine particles increases sharply, requiring more polymer to wet, which in turn increases the matrix content required to achieve the same fluidity. The grading ratio needs to be experimentally optimized based on the target filling rate and matrix viscosity, rather than simply "half coarse and half fine".

Gradient structure: division of labor between flexibility and absorption at different thickness positions

The third path is to construct a gradient in the thickness direction. One side of the sheet (near the surface to be pasted) adopts a higher filling rate to provide magnetic loss and absorption; The other side (outer surface) adopts a lower filling rate to preserve the continuity and flexibility of the polymer. When bending, the outer layer with low filling rate bears the main deformation, while the inner layer with high filling rate bears smaller strain.

Implementation method and cost of gradient structure

The implementation of gradient structure includes multi-layer stacking and packing settlement/centrifugation during the forming process. The multi-layer stacking process is mature, but the interlayer interface may become a stress concentration point during bending; The gradient of settling/centrifugal forming is continuous and has no obvious interface, but the process control difficulty is higher. The cost of gradient structure is an increase in thickness and process complexity. For scenarios with tight thickness budgets (such as 0.1-0.3 mm inside mobile phones), the multi-layered stacking of gradient structures may occupy the already limited space and need to be balanced with thickness constraints.

Selection and judgment of flexible soft magnetic wave plate based on the "filling rate window"

Firstly, use the filling rate as a selection parameter to confirm, rather than just looking at the results of magnetic permeability and flexibility

Magnetic properties and flexibility are the two 'outputs' of filling rate, while filling rate is the' input '. Request the supplier to provide the volume fraction or mass fraction of the filler, as well as the magnetic permeability, loss, and bending durability data at that filling rate. If the supplier only provides magnetic performance and flexibility data without filling rate, the trade-off between the two sets of data cannot be understood, and it is also impossible to determine whether the solution falls in the "danger zone" near the percolation threshold.

Secondly, confirm the bending radius and number of bends of the target application, and then evaluate whether the filling rate is acceptable

One time attachment to a fixed surface and repeated bending assembly are two different stress modes. The former mainly examines the retention of magnetic properties after static bending, while the latter requires attention to the impedance matching stability after cyclic bending. A sheet with a filling rate close to the percolation threshold may pass through static bending, but the magnetic drift after cyclic bending may exceed expectations. When selecting, the supplier should be required to provide magnetic performance retention data at the target bending radius and number of cycles.

Thirdly, in scenarios where the filling rate is limited, priority should be given to evaluating sheet-like fillers and bimodal grading schemes, rather than compensating for magnetic performance by increasing thickness

If there are hard constraints on flexibility in the application scenario (such as wearable devices, curved shells), the filling rate cannot be infinitely increased. At this time, the advantage of the aspect ratio of sheet-like fillers and the stacking efficiency of bimodal gradation are effective means to improve magnetic performance without sacrificing flexibility. Although increasing thickness can compensate for the length of the absorption path, it will occupy space and reduce flexibility, making it not the preferred choice for scenarios with limited filling rates.

Fourthly, in the gradient structure scheme, the interlayer interface is treated as an independent verification term

The gradient structure of multi-layer stacking, where the interlayer interface is the stress concentration location during bending. When selecting, it should be confirmed whether the supplier provides interlayer integrity data after bending (such as cross-sectional microscopic observation or peel strength testing), and whether there is local mismatch in magnetic properties at the interface due to sudden changes in filler concentration.

Advanced Institute (Shenzhen) Technology Co., LtdThe flexible soft magnetic wave plate product line covers sheet-like FeSiAl and carbonyl iron powder composite systems, providing magnetic performance retention data for filler volume fraction, percolation threshold range, and target bending radius, as well as comparative evaluation of three filling rate optimization schemes: sheet-like filler, bimodal grading, and gradient structure.

The product supports matching the filling rate window with the filling form based on the bending radius, bending times, and thickness budget, helping engineers find a quantifiable balance between flexibility and absorption performance. For more technical information, please visithttp://www.avanzado.cn/.

Contact Us

Company: Xianjin Yuan (Shenzhen) Technology Co., Ltd.
Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China
Tel: 0755-22277778  |  13826586185
Email: duanlian@xianjinyuan.cn
Website: http://www.avanzado.cn/
Hotline
0755-22277778
13826586185(Mr.Duan)
Wechat QRcode Wechat QRcode