
Hotline:0755-22277778
Tel:0755-22277778
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn
Technical Note / Antenna Integration
In a 5G MIMO module, the center distance between the two antennas is only 8mm, and the measured isolation is about -12dB. The solution is to place a magnetic wave absorbing plate between the two antennas. After adding it, the isolation did improve (with a common amplitude of several dB), but in the overall OTA testing of the whole machine, the antenna efficiency also dropped by a few percentage points. The project team is caught in a dilemma: the indicators seem to have "improved", but the usability has decreased.
This is not a matter of materials, but a misalignment of roles. The essence of a waveplate isTransform energy into heat——It cannot distinguish whether this magnetic flux comes from a noise source or from your own antenna. After being placed in the near-field of the antenna, it weakens both coupling and radiation. Only by understanding this matter can we talk about 'using it correctly'.
When approaching the antenna, whether the same piece of magnetic material works according to "magnetic path guidance" or "energy dissipation" depends on the ratio of μ 'to μ "in the formula, rather than whether it is called a wave absorbing plate or a magnetic insulating plate.
The first question for selectionDo you want to 'bring in the magnetic flux' or 'eat up the magnetic flux'? The former chooses high μ 'and low μ', while the latter chooses high μ '. Both may be labeled as "high magnetic permeability" on the specification sheet, but in completely opposite directions.
Adding any lossy material to the near-field of the antenna will simultaneously rewrite three quantities. The first one isefficiencyThe absorption plate converts a portion of the energy that should have been radiated into heat, resulting in a decrease in radiation efficiency, which is strongly related to material loss, coverage area, and distance from the antenna. The closer the distance, the higher the proportion of being "eaten up", which is why "the closer you stick, the better the effect" holds true in noisy scenes but becomes a trap in antenna scenes.
The second one isResonance and bandwidthThe material's μ 'will change the equivalent magnetic medium environment near the antenna, thereby altering the inductance and causing a shift in the resonant frequency; The introduced loss at the same time will reduce the Q value, making the bandwidth wider but the efficiency lower. Many cases where the standing wave improves after adding a wave absorbing plate are essentially about the resonance being pulled off and re matched, which does not necessarily mean an improvement in performance.
The third quantity is usually pursued:isolationThe coupling between the two antennas mainly propagates along the ground plane current, surface waves, and spatial near-field; Inserting a wave absorber in this path can indeed weaken some of the energy transfer. The extent of improvement depends on whether the position is directly facing the area where the coupling current is most concentrated, whether the band width covers the magnetic flux path, and whether the material's μ "in the target frequency band is large enough.
If it is necessary to use a waveplate for decoupling, there is only one principle for positioning:Place it on the coupling path between two antennas, rather than directly above the antennas or near the feed point.The common practice is to place a narrowband along the perpendicular line between the two antennas, with a width covering the area with the strongest coupling, leaving a margin on both sides to avoid pressing on the antenna body. This not only cuts off the main magnetic flux path, but also distinguishes the absorbed energy from the radiation of the antenna itself.
On the material side, priority should be given to selecting formulas with high μ "and relatively low μ 'within the target frequency band to reduce disturbances to inductance and resonance. In engineering practice, it is also necessary to accept a basic fact: decoupling comes at a cost, and the improvement is often on the order of several dB, while efficiency loss is approximately positively correlated with coverage area. So the more common sequence is to first use passive structural means (neutral line, decoupling network, floor slotting, parasitic unit, EBG structure), and the absorbing wave plate is used as a supplement to the limited space, rather than the first choice.
A common misjudgmentS21 improvement ≠ overall improvement. The increase in isolation may only convert energy into heat, and if the antenna efficiency and total radiated power (TRP) decrease together, the OTA results will actually be worse. Efficiency and isolation must be measured simultaneously.
In the millimeter wave band, the spacing between array elements is usually only on the order of half a wavelength, and the antenna and packaging height are pressed to the limit, with almost no space to insert a piece of absorbing material. The more common methods in this frequency band are packaging level isolation walls, EBG, and low loss dielectric layers. The role of the absorbing wave plate is reduced to two specific positions: one is to suppress the resonance and surface waves inside the packaging cavity, and the other is to wrap the edges of the module to reduce coupling to adjacent modules.
At this point, the requirements for materials are also different from those for low frequencies: they should be extremely thin, have high thickness uniformity, and be insensitive to incident angles. The wavelength of millimeter waves is very short, and a material with a large thickness tolerance can cause local phase differences, which can actually distort the directional pattern; The impedance mismatch caused by the change in angle will significantly reduce the nominal attenuation value under oblique incidence. To evaluate such applications, testing conditions that are close to the actual incident angle and polarization direction must be used.
This is the easiest type of scenario to choose incorrectly. What is required for NFC (13.56MHz) and wireless charging (100kHz level)Magnetic circuit guidanceConcentrate the magnetic flux in the effective area of the antenna and bypass the metal behind it using high μ 'and low μ' 'magnetic sheets, thereby improving the reading distance and coupling coefficient, and suppressing eddy currents. Using the absorption approach (pursuing high μ ") will dissipate the energy that should have been guided, resulting in shortened reading distance, decreased charging efficiency, and increased coil temperature.
In this type of design, the relationship between thickness and μ 'is also a trade-off: there is a marginal decrease in the improvement of the read distance by the thin film, and beyond a certain thickness, the increased magnetic resistance and structural stress begin to backfire. A more reliable approach is to use the magnetic disk as part of the magnetic circuit for parameterized simulation, and then verify it with measured reading distance and Q value, rather than copying "the thicker the better".
Three sets of data are indispensable:Radiation efficiency(or OTA/TRP, TIS)isolation(S21/S12, including actual matching status)Resonance and bandwidth(Offset of return loss curve). When measuring the isolation degree, it must be carried out in the assembled state of the whole machine, and the empty board data is often opposite to the whole machine data; When measuring efficiency, it is necessary to cover the actual handheld or face mounted working conditions, as the human body and the casing will completely change the near-field distribution.
If the three sets of data show "improved isolation, decreased efficiency, and resonance offset", then a clear trade-off judgment needs to be made: in terms of system capacity and sensitivity, does the improved isolation really result in better actual throughput? Many times the answer is negative - especially in low coupling frequency bands, efficiency is the scarcest resource.
Decision List① Does coupling mainly come from ground current or spatial near-field? ② Is there any passive decoupling method that can be used first? ③ Is the material's μ ″ sufficient and μ ′ too large within the target frequency band? ④ How much budget is left for the decrease in efficiency? ⑤ Have you viewed all three data items in the complete machine state at the same time?
Every improvement made by placing magnetic materials next to the antenna comes with a cost. Treat it as a transaction that requires accounting, rather than a free optimization, so that antenna design will not be misled by short-term S21 curves.
For more technical information on magnetic absorbing materials, magnetic separators, and conductive shielding materials, please visitwww.avanzado.cn.
Contact
Company:Xianjin Yuan (Shenzhen) Technology Co., Ltd.
Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China
Tel: 0755-22277778 13826586185
Email: duanlian@shturl.cc /9Q5x
Advanced Institute (Shenzhen) Technology Co., Ltd, © two thousand and twenty-onewww.xianjinyuan.cn. All Rights Reserved.Guangdong ICP No. 2021051947 sitemap