Our main products include flexible substrate coating, shielding materials, absorbing materials, precious metal slurries, and more!

banner
Current:Home >Company news >Frontier News >Magnetic waveplate: Triangular constraints on frequency band, bandwidth, and thickness
先进院(深圳)科技有限公司

Hotline:0755-22277778 Tel:0755-22277778 
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn

Frontier News

Magnetic waveplate: Triangular constraints on frequency band, bandwidth, and thickness

Time:2026-11-19Number:19

Technical Note  /  Absorber Bandwidth

A project team hopes to use a "single" absorbing wave plate to simultaneously suppress three resonant points inside the cavity at 900MHz, 2.4GHz, and 5GHz. They selected a magnetic wave absorbing plate labeled as "suitable for 0.5-6GHz" and covered the entire shielding cavity. According to actual measurements, each of the three frequency points only decreased by 1-2dB. The problem is not with the product, but with the pronunciation: the labeled "applicable frequency band" is usually the range where the attenuation has not been significantly reduced, which does not mean that "there is available absorption within this frequency band". The true dominant absorption peak is only around 3GHz, and the μ "at 900MHz is still at a low level.

Magnetic wave absorbing plate is not a "black sponge", it is a designed magnetic loss curve. Understanding where the peak of this curve is, how wide the peak is, and what the cost is, will prevent the selection of "coverage frequency band" as "absorption intensity".

01The true meaning of "coverage frequency band" is peak position

The absorption capacity of magnetic wave absorbing plates is dominated by the imaginary part of the complex magnetic permeability, μ ". The value of μ "remains low within a wide range, only rising to a peak near the resonance frequency, and rapidly falling back after the peak. So there are only three truly valuable pieces of information on a frequency response curve: peak frequency, peak height, and the width at which both sides of the peak decay to half. Matching these three quantities to your noise frequency point is called 'coverage'.

μ 'and μ' are two sides of the same coin. The larger the μ ', the easier the material is to magnetize and the more effective the thin film is; But once resonance occurs, the material changes from 'magnetic conductivity' to 'dissipation', with a steep decrease in μ 'and an increase in μ' '. This is also why the same material exhibits "magnetization" in the low frequency range and "absorption" in the high frequency range, but both cannot be maximized simultaneously.

The first question for selectionIs your noise single point or narrowband? If it is narrowband, aligning the peak position of the material with it yields the highest efficiency; If it is broadband, it must accept "exchanging thickness for bandwidth" or accept multi-point stacking.

02Snoek limit: high magnetic permeability and high frequency are inherently mutually exclusive

This is not due to a poorly prepared formula, but rather due to the physical constraints of the materials. For a given magnetic material, there is an upper limit to the product of the initial permeability and the natural resonance frequency, which is commonly referred to as the Snoek limit: the higher the μ ', the lower the resonance frequency. In other words, in order to achieve a high level of μ ', the available frequency band of the material must be compressed to low frequencies; To make the absorption peak appear above GHz, it is necessary to give up some of the low-frequency magnetic permeability.

This constraint explains a recurring purchasing illusion: suppliers provide specifications of "μ '=300" and "applicable to 6GHz", which may seem like the best of both worlds, but often fail quickly above 3GHz in actual testing. The parameters themselves are not wrong, but they were measured separately at two different frequencies, and combining them together constitutes misleading information.

03Flattening: Three paths to push up the resonance frequency

Since the upper limit is determined by the material itself, engineering can only focus on "changing materials" and "modifying shapes". The three most commonly used paths are:

Shape anisotropy.Pressing spherical powder into extremely thin, flat powder with a large aspect ratio makes it more difficult for magnetization to flip along the thickness direction, and significantly increases the resonance frequency. This is the fundamental reason why almost all GHz absorption wave plates use flat metal powder instead of ferrite.

Composition and saturation magnetization.Increasing the saturation magnetization can elevate the overall Snoek product, but at the cost of corrosion resistance and cost. Iron silicon aluminum is relatively balanced between the two, while iron cobalt based and rare earth modified systems further push the upper limit to millimeter waves, but the process window is narrow and the price is high.

Orientation and insulation coating.Stacking flat powders parallel to the plane of the sheet can achieve high effective magnetic permeability within the surface; Each powder is wrapped in resin insulation to suppress eddy currents and prevent the material from degrading into a conductor at high frequencies. Whether the orientation is done well or not directly determines whether the same formula is "thin and effective" or "thick and useless".

material system Typical applicable frequency band Characteristics and Costs
MnZn ferrite Hundred kHz - Several MHz High μ 'and low cost; Thick and brittle, with basic failure in the GHz range
NiZn/Hexagonal Ferrite Ten MHz - Several hundred MHz (partially up to GHz) The main force of high-frequency ferrite is still limited by Snoek and tends to be thicker
Carbonyl iron flat powder Hundreds of MHz -3GHz High saturation magnetization and moderate cost; High density, heavy emphasis
FeSiAl flat powder 1-6GHz (some formulas have higher frequencies) Corrosion resistance and high-frequency balance are universal choices in the GHz band
FeCo/rare earth modification 3GHz - Millimeter Wave The peak position is the highest and can be made extremely thin; Cost and process window are the main obstacles
Amorphous/nanocrystalline thin strip Low frequency dominant (magnetic isolation, magnetic circuit guidance) Extremely high in μ 'and low in μ' ', suitable for guidance rather than absorption

This chart can answer most of the questions about why this product is not effective in my frequency band: it's not that the product is poor, but that the peak position is not in your frequency band. Within the same frequency band, first check if the peak positions are aligned, and then compare the peak height and thickness. Reversing the order will result in repeated trial and error.

04Bandwidth and thickness: another unavoidable lower limit

Under the given thickness and reflection coefficient target, there is a theoretical upper limit to the achievable bandwidth of a single-layer absorbing material (usually referred to as the Rozanov relationship): if you want to continue pressing down on the low-frequency end, you can either thicken it or increase the μ 'and μ' in the low-frequency band. This is not contradictory to the slogan of "thinner, more advanced" - it only indicates that thinning will inevitably come at the cost of sacrificing low-frequency bandwidth.

The conversion in engineering is very direct: with the same formula, the thickness is halved, and the absorption near the peak roughly decreases proportionally, while the effective bandwidth at the low-frequency end is significantly narrowed; To maintain the original bandwidth, one can only choose a formula with higher magnetic permeability or a higher filling ratio, which returns to the constraint of Snoek limit. The three constraints interlock with each other, and if any one is broken, the other two will inevitably yield.

05Three paths covering multiple frequency bands

Path method Suitability and Cost
Multi-layer stacking Two formulas with different peak positions are combined to form a bimodal or broadened unimodal structure The widest coverage; Thickness superposition, impedance transition and adhesive layer need to be considered between layers
Hybrid structure Magnetic layer+several micron metal layer, unabsorbed noise is reflected back to the magnetic layer for secondary absorption Equivalent lengthening of absorption path makes high-intensity noise sources more effective; The metal layer needs to be insulated and isolated
Partition attachment Use different formulas in different regions according to hotspot frequency bands and locations The most cost-effective and targeted materials; Need near-field scanning data support, slightly complex process

The most effective approach in actual projects is often not to use "more expensive materials" other than the third one, but to first identify the hotspots: the noise frequencies at different locations are not the same, and the fundamental frequency and low order harmonics are mainly present above the chip. Connectors and cable outlets often protrude more on higher order harmonics. It is not economical to have one piece of material handle both types of problems simultaneously.

06The four easiest places to misjudge when reading curves

Consider 'applicable frequency band' as' effective bandwidth '.The former often refers to the interval where μ "has not yet returned to zero, while the latter corresponds to available attenuation. The criterion for judgment should be 'what is the personally measured attenuation at the target frequency point', rather than the interval specified in the specification sheet.

Consider reflection loss as a near-field indicator.The reflection loss curve of - XdB belongs to the far-field impedance matching scenario, which is two evaluation systems compared to board level near-field suppression; The near-field should observe transmission attenuation or power loss, and indicate the fixture, distance, and sample size.

Ignore the superposition of thickness and adhesive layer.The "thickness" in the specifications often only refers to the magnetic layer. After adding insulation film and backing adhesive, the total thickness will significantly increase, and the adhesive layer does not contain magnetic powder, which does not contribute to absorption but actually occupies stacking space.

Ignore temperature and angle.The peak position drifts with temperature, and the peak height also varies with the incident angle. The measured values of the whole machine under high temperature conditions often differ significantly from the samples at room temperature, and this must be confirmed separately during the verification phase.

07A decision table

Ask four sentences in order① Where is the noise frequency, narrowband or broadband? ② Which type of material in this frequency band has a corresponding peak position of μ "? ③ What is the total thickness allowed for the available stacking space? ④ Will the overall temperature and bonding position cause a shift in peak position? After four Q&A sessions, the rest is just gear selection, not guessing.

The true technical content of magnetic wave absorbing plates lies not in "how much they can absorb", but in "where they can absorb and how much thickness they have paid for it". Treating it as a curve that needs to be aligned with the frequency band is much more reliable than treating it as a piece of material that can be easily pasted.

For more technical information on magnetic absorbing materials, conductive shielding materials, and precious metal pastes, please visitwww.avanzado.cn.

Contact

Contact Us

Company:Xianjin Yuan (Shenzhen) Technology Co., Ltd.

Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China

Tel: 0755-22277778   13826586185

Email: duanlian@shturl.cc /Mkxd

Hotline
0755-22277778
13826586185(Mr.Duan)
Wechat QRcode Wechat QRcode