
Hotline:0755-22277778
Tel:0755-22277778
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn
Technical Note / Reliability Validation
A magnetic wave absorbing plate was measured to attenuate by 8dB around 2.4GHz on a room temperature sample, with beautiful data and complete specifications. After being installed in the whole machine and stored at 85 ℃ for 500 hours, the attenuation at the same position was only 4dB, and there was also a significant uplift at the edge during retesting. This type of story is not uncommon in high reliability projects, and the problem is not that the material has deteriorated, but in the evaluation method:Room temperature single point data is just an admission ticket, it does not answer how much capacity the material still has under the combined effects of temperature, humidity, stress, and time.
The absorption capacity of a waveplate is roughly proportional to the product of the thickness and the length of the wave. Both of these are unstable: the peak position of μ "will drift with temperature, and the thickness will decrease due to the creep of the adhesive layer. What reliability verification needs to do is to force these two variables out in a real environment.
The influence of temperature on magnetic properties can be seen in two material systems. Ferrite is constrained by Curie temperature, and as it approaches the Curie point, its magnetic permeability rapidly decreases and its peak position shifts significantly; The Curie temperature of the metal soft magnetic powder composite system is much higher, and the magnetic properties are less sensitive to temperature. However, temperature can affect the results through two other pathways: a decrease in the modulus of the resin matrix (relaxation of the bonding surface) and accelerated oxidation of the metal powder.
Therefore, the word 'temperature resistance' has two meanings on absorbing plates and must be asked separately:Temperature upper limit of magnetic layerHow long can the performance be maintainedUpper temperature limit of adhesive layer/substrateCan the structure support it. Suppliers often give a vague value, but in engineering, it is the latter that truly determines failure - the compression creep caused by the softening of the adhesive layer will slowly reduce the total thickness under long-term high temperature, and the attenuation will decrease accordingly, and this process is irreversible.
The humid and hot environment rarely directly damages the absorbing plate. It does three slow things: allowing the resin matrix to absorb moisture and expand, and reducing interfacial adhesion; Oxidation of the surface of metal powder that has not been completely coated, resulting in degradation of both μ "and insulation properties; Hydrolyze the polar components of the adhesive layer, and the peel strength decreases over time. After the superposition of the three, the manifestation is a gradual decline in attenuation, edge warping, and local adhesion failure.
Salt spray attacks the metal parts more directly. The composite structure of bare copper and incomplete coating will quickly corrode in a chlorine containing environment, while for the absorbing wave plate, once the insulation coating of the powder is damaged, the material will locally "transform into a conductor" at high frequencies, causing an increase in eddy current losses and a decrease in absorption performance instead of an increase. Coastal, shipborne, outdoor base station and other scenarios should include the salt spray level in the specifications instead of leaving it as an "optional".
A waveplate is a thin film with almost no compression rebound reserve, and its reliability highly depends on the consistency of the bonding area and the thickness of the adhesive layer. The first places to encounter problems under random vibration are usually narrow strips, corners, and surfaces with large curvature: the adhesive layer is locally subjected to shear, and the edges gradually peel off. Once peeling begins, the gaps expand along the edges. That's also why the same material performs well on flat surfaces, but quickly fails on flange edges and curved corners.
The scenarios of repeated bending (FPC dynamic area, wearable structure) also require separate assessment of fatigue life. The difference in modulus between magnetic powder and matrix will cause microcracks at the bending interface, initially showing a slight decrease in attenuation, and later resulting in powder loss. In engineering, the dynamic bending zone is usually excluded from the scope of use of absorbing wave plates, or a low modulus, high elongation formula is used instead, and a minimum bending radius is specified.
The explanation of aging tests relies on accelerated models. The most commonly used method is still the Arrhenius approximation: for every 10 ℃ increase in temperature, the chemical reaction rate roughly doubles, that is, the acceleration factor can be set at 2(ΔT/10)estimate. Running at 85 ℃ for 500 hours, converted to a working condition of 45 ℃, is equivalent to thousands of hours of equivalent time - sufficient in magnitude, but the premise is that the mechanism being evaluated is truly a temperature driven chemical reaction, rather than simply physical relaxation or mechanical fatigue.
The real failure is often a multi mechanism coupling: the creep of the adhesive layer belongs to a mechanical process, which is sensitive to temperature but does not conform to Arrhenius; Interface hydrolysis requires the involvement of humidity; Oxidation depends on both temperature and oxygen partial pressure. Therefore, extrapolation results should be used as a basis for sorting and screening, rather than a "lifespan commitment". The prudent approach in engineering is to group the acceleration based on stress types (thermal, wet, and mechanical), then extrapolate each group separately, and finally take the most conservative group as the design margin basis.
The most common disagreement in the procurement and quality process comes from the fact that the specification sheet only has typical values and no boundary conditions. A determinable specification should include at least four things: testing frequency and fixture, sample size and bonding surface material, aging conditions and retesting time, and acceptable degradation amplitude (such as attenuation reduction not exceeding 2dB, lifting area not exceeding a certain proportion of bonding area). If one item is missing, both parties can only argue about whether it is considered invalid or not.
Checklist for Acceptance QuestionsWhat are the testing frequency points and fixtures? Is the sample coated with adhesive and on what surface? How to define the aging conditions and retesting time points? What is the allowable attenuation and appearance degradation range? Only when all four are complete can the data have comparative significance.
In high reliability scenarios, the competitiveness of absorbing wave plates is never reflected in the line of numbers at room temperature, but in "how much is left after running one round of environmental testing". Putting validation at the forefront is much cheaper than repeatedly changing materials during mass production.
For more technical information on magnetic absorbing materials, conductive shielding materials, and precious metal pastes, please visitwww.avanzado.cn.
Contact
Company:Xianjin Yuan (Shenzhen) Technology Co., Ltd.
Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China
Tel: 0755-22277778 13826586185
Email: duanlian@shturl.cc /pX2c
Advanced Institute (Shenzhen) Technology Co., Ltd, © two thousand and twenty-onewww.xianjinyuan.cn. All Rights Reserved.Guangdong ICP No. 2021051947 sitemap