Our main products include flexible substrate coating, shielding materials, absorbing materials, precious metal slurries, and more!

banner
Current:Home >Company news >Frontier News >Ferrite absorbing materials: advantages of high resistivity and boundary of frequency
先进院(深圳)科技有限公司

Hotline:0755-22277778 Tel:0755-22277778 
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn

Frontier News

Ferrite absorbing materials: advantages of high resistivity and boundary of frequency

Time:2026-11-20Number:43

Technical Note  /  Ferrite Absorbers

A sintered ferrite sheet is placed behind the NFC coil, resulting in a significant increase in reading distance of 13.56MHz; Moving the same material next to the 2.4GHz module almost shows no effect. Engineers often oscillate between two reactions: Is ferrite okay or not? The answer depends on the frequency.In the range of hundreds of kHz to tens of MHz, ferrites have almost no competitors; Once it enters the GHz band, its physical upper limit gives way to flat metal soft magnetic powder.

To understand this boundary, two things need to be clear at the same time: why is ferrite strong at low frequencies, and what is blocking it from high frequencies.

01Bottom card: Natural high resistivity

Ferrite is a ceramic magnetic material with a resistivity several orders of magnitude higher than metals - MnZn system is in the lower range, while NiZn system can achieve very high resistivity. This means that the eddy currents induced by the alternating magnetic field inside the material are significantly suppressed, and the magnetic losses mainly come from the intrinsic mechanisms during the magnetization process, rather than the additional heating and shielding caused by the "current winding around the material".

This is very valuable in engineering. Metal soft magnetic powder must be individually insulated and coated to suppress eddy currents. Once the coating is damaged during wet heat, bending, or sintering, the material will "become a conductor" at high frequencies, with surface reflection increasing and absorption decreasing; Ferrites are naturally not prone to this hazard. So, at the hundred MHz level, a well made NiZn ferrite has losses closer to "designed losses" rather than "losses caused by process fluctuations".

Remember one sentenceThe advantage of ferrite is not "higher magnetic permeability", but "maintaining usable magnetic loss at high resistivity".

02Upper limit: The saturation magnetization determines the ceiling

The saturation magnetization of ferrite is much lower than that of iron-based alloys, which directly lowers the upper limit of its Snoek product - the "initial magnetic permeability x resonance frequency". To achieve a high μ ', the resonance frequency needs to move towards a lower frequency; To achieve resonance in GHz, μ 'can only be made very low. This is a constraint at the component level that cannot be broken through by craftsmanship.

The response of metal soft magnetic powder is "shape modification": the powder is compressed into thin sheets, and shape anisotropy is used to provide additional anisotropic fields, pushing the resonance frequency up by an order of magnitude. Ferrite, as a ceramic, is difficult to achieve the same effect through the same flattening, so almost all absorbing wave plates in the GHz band are metal powder composite systems.

The only exception is hexagonal ferrite (such as barium ferrite, strontium ferrite). It itself has extremely strong magnetic crystal anisotropy, and the equivalent anisotropy field is much higher than that of ordinary spinel ferrite, so the upper limit of Snoek is significantly raised, which can achieve absorption in GHz or even higher frequency bands. The cost is that the formula and sintering window are narrow, the cost is high, and it is usually used in thin film or composite form instead of large sintered pieces.

system Typical frequency band μ 'level main purpose
MnZn Hundred kHz - Several MHz Can be done very high Wireless charging with low-frequency magnetic isolation and common mode suppression
NiZn Ten MHz to several hundred MHz moderate NFC magnetic sheet, HF/VHF band absorption and suppression
Hexagonal ferrite GHz and above lower High frequency thin film absorption and millimeter wave research applications
Flexible composite type With the packing system, it is mostly in the MHz range Medium-low Thin magnetic insulation and local suppression that can be die cut

03Two forms: sintered sheet and flexible composite sheet

Both are ferrites, and the product form determines where it can be used. The sintering process involves casting, stacking, sintering, and cutting, resulting in ceramic sheets with high magnetic density, good consistency, and a thickness that can be made thin, but brittle and limited in size due to sintering shrinkage and warping, and cannot be bent. Flexible routes combine ferrite powder with rubber or resin, sacrificing some filling density in exchange for bendable, die cut, and adhesive surfaces.

dimension Sintered ferrite sheet Flexible composite sheet
magnetic properties High filling density, strong μ 'and magnetic flux carrying capacity Due to the limitation of resin proportion, μ 'is usually low
machinery Crispy, prone to edge breakage, cannot be bent, die-cutting requires specialized techniques Flexible, die cut, and able to fit curved surfaces
size Due to sintering shrinkage and warping limitations, larger sizes are more difficult to achieve Roll material supply, size limited by die-cutting capability
Typical occasions Magnetic isolation and suppression within flat and fixed structures Curved surfaces, narrow borders, and locations that require buffering and impact resistance

There is an easily overlooked criterion for selection:Structural stressThe sintered sheet is prone to cracking under assembly stress, screw compression, and thermal expansion. Once the crack passes through the magnetic circuit, the efficiency of magnetic flux guidance will significantly decrease; Although flexible sheets have lower μ ', they can absorb tolerances and deformations, often providing more stable mass production results in thin wearable and curved structures.

04Same system, two personalities: low loss and high loss

Ferrite can be used for both "magnetic isolation" and "absorption", but the difference lies in how the formula and sintering process arrange magnetic losses. When used for magnetic circuit guidance (NFC, wireless charging), the pursuit is high μ 'and low μ' ', hoping that the magnetic flux can pass through without loss as much as possible; When used to absorb noise, it is deliberately increased to allow energy to dissipate inside the material. The former fears loss, while the latter wants loss, these are two opposite goals in the same material system.

The regulatory measures include component substitution, grain size and porosity, sintering temperature and atmosphere. Excessive grain size and porosity can introduce additional losses; On the other hand, in order to produce high loss absorbing models, controllable non-uniformity will be intentionally created. Therefore, when purchasing, we cannot only look at whether the "μ 'is high or not", but also confirm whether this product is a "low loss type" or a "high loss type", as their performance at the same frequency point may be completely opposite.

05The boundary line with metal soft magnetic powder

criterion Choose ferrite Select metal soft magnetic powder
Target frequency band 100kHz - Hundreds of MHz More relaxed above 1GHz
Main demands Magnetic circuit guidance, low-frequency suppression, cost sensitive GHz near-field absorption, thinning
structurally conditioned Flat, Acceptable Brittleness, and Thickness Should be bent, thin, and directly attached to the circuit
Reliability Focus Cracking, warping, Curie point Coating integrity, oxidation, and insulation degradation
cost structure Raw material and sintering energy consumption; The cost of large-sized products is rising rapidly Metal powder and insulation technology; The cost of high filling formula is high

The boundary line is not a fixed frequency, but the intersection of a set of constraints: target frequency band, available thickness, structural stress, and cost. In the same project, using ferrite for the magnetic isolation part and metal soft magnetic powder for the GHz absorption part is a completely normal combination, rather than a "one or two" stance issue.

06Four quantities to be monitored during acceptance inspection

firstlyFrequency response curves of μ 'and μ' 'And it depends on whether it is a low loss or high loss type; SecondSaturation magnetization intensityIt determines whether it will saturate under high current or strong magnetic field, especially in wireless charging and power magnetic circuit; ThirdlyCurie pointThe magnetic properties of sintered MnZn system decay rapidly at high temperatures, and a margin should be left near the heat source; Four isMechanical integrityIncluding warpage, edge breakage rate, and cracking after thermal shock.

The value of ferrite absorbing materials lies not in their ability to absorb, but in their ability to effectively manipulate magnetic flux tubes in the correct frequency band with almost no eddy current losses. By combining frequency boundaries with shape constraints, this material will transition from an outdated choice to the most stable choice.

For more technical information on magnetic absorbing materials, shielding materials, and precious metal pastes, please visitwww.avanzado.cn.

Contact

Contact Us

Company:Xianjin Yuan (Shenzhen) Technology Co., Ltd.

Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China

Tel: 0755-22277778   13826586185

Email: duanlian@shturl.cc /8R0U

Hotline
0755-22277778
13826586185(Mr.Duan)
Wechat QRcode Wechat QRcode