Our main products include flexible substrate coating, shielding materials, absorbing materials, precious metal slurries, and more!

banner
Current:Home >Company news >Frontier News >Strong adhesive copper foil tape: Where does the peel strength come from, and at what cost
先进院(深圳)科技有限公司

Hotline:0755-22277778 Tel:0755-22277778 
Mobile:13826586185(Mr.Duan)
Fax:0755-22277776
E-mail:duanlian@xianjinyuan.cn

Frontier News

Strong adhesive copper foil tape: Where does the peel strength come from, and at what cost

Time:2026-11-20Number:34

Technical Note  /  Adhesion Engineering

The same roll of strong adhesive copper foil tape cannot be peeled off when applied to a smooth aluminum shielding cover, but it can be easily removed when applied to the solder mask surface of FPC; The room temperature peeling test performed well, and after running at 85 ℃ for high temperature storage, the edges began to curl.Strong adhesion "has never been a fixed attribute, it is the result of four factors: adhesive, veneer, process, and time.A specification sheet that only provides a peel strength number cannot answer what will happen on your production line.

To determine whether a piece of tape can "stick" to a certain structure, it is necessary to first break down the bonding into several stages that can be evaluated separately.

01Three commonly confused indicators

indicator What is being assessed Performance when making a mistake
Initial adhesion (stack) The ability to stick with light pressure determines the "grip" when attaching Slippery when pasted, difficult positioning, and automatic line dropping
Stick (sheet) Resistance to displacement under long-term shear force Slow displacement and edge climbing after vibration or temperature cycling
Peel strength (peel) The force required to tear open at a certain angle and speed During repair, components may be lifted or delaminated due to stress

The term 'strong adhesion' commonly used in the market refers to high adhesion and peel strength, but at the cost of lower initial adhesion and poor fluidity. On the other hand, adhesives with good initial adhesion often have lower molecular weight and stronger fluidity, which can compromise their long-term adhesion and temperature resistance performance. There is no free lunch among the three, the first step in choosing is to confirm which one you really need.

02The real reason for not sticking: surface energy

The adhesion of pressure-sensitive adhesives relies on two things: the adhesive can "wet" the surface, and the molecular chains can form sufficient interactions with the surface. The prerequisite for wetting is that the surface tension of the adhesive is lower than the surface energy of the veneer. Once the surface energy of the veneer is too low, the adhesive only "sticks" on top and will peel off as a whole under slight stress - this is not related to the viscosity of the adhesive, and changing to a stronger adhesive is also ineffective.

Covered with veneer Surface energy level countermeasure
Clean metals (copper, aluminum, stainless steel) higher Conventional strong adhesive formula is sufficient; The focus is on oil and dust removal
Solder mask layer, polyimide moderate Choose the right polarity for the adhesive; Pay attention to surface contamination and residual release agents
Low surface energy plastics such as PP/PE low It is necessary to perform corona or plasma treatment, or add a primer
Silicone rubber, LSR and silicone release surface Very low Conventional pressure-sensitive adhesives are generally ineffective and require specialized silicone adhesive or primer
Powder coating, rough surface Depends on the coating Fill the gap with thicker adhesive, but the contact area decreases and the peel strength is difficult to increase

The practical value of this table lies in its ability to transform the issue of "stickiness" from a performance problem of adhesive tape to an interface engineering problem. When encountering the question of 'this tape works well on A but not on B' in a project, the answer is almost always on the surface energy, contamination, or roughness of B, rather than on the adhesive itself.

Remember one sentenceGlue can only 'wet' surfaces that can be wetted. Where the surface energy is too low, even the strongest adhesive will only stick to it.

03Time and pressure: The values measured on the production line are often not true

The final bonding strength of pressure-sensitive adhesive requires time to establish: the adhesive layer flows into the micro bumps under pressure, and the molecular chains gradually interact with the surface, which often takes several hours to a day to complete. Tear off immediately after pasting, and the measured value is the superposition of initial adhesion and partial peel strength, which will be significantly lower; Based on this, the production line judged that the adhesive was not enough, so they replaced it with a more sticky adhesive, which actually led to residual adhesive problems in the future.

Pressure is equally important. The pressure of manual attachment is usually only a fraction of that of roller pressing, and the peel strength of the same tape can differ by twice between two processes. A more secure approach in engineering is to include the compression pressure, roller hardness, and speed in the work instructions, and to specify the static time (or set low-temperature acceleration conditions) after attachment before conducting random inspections.

04The Cost of Strong Stickiness: Four Hidden Costs

Residual glue and repair.The higher the peel strength, the more difficult it is to clean the adhesive left on the surface after tearing. The most common cycle on the production line is to perform secondary bonding if it is not cleaned thoroughly. When selecting, it is important to clarify whether this adhesive is a clean peelable type or a permanent adhesive type, as the two have completely different repair strategies.

Overflow and pollution.Strong adhesive formulas typically have high molecular weight and poor flowability, but they still flow slowly towards the edges under temperature and pressure. The overflowing glue entering the connector and contaminating the solder pads is causing electrical performance issues rather than appearance problems.

Mechanical damage during tearing.High peel strength on weak FPC or fine pitch components, the stress at the moment of tearing is sufficient to lift up the solder pad or tear the substrate. For this type of structure, it is better to sacrifice some of the adhesive force than to let repair turn into scrap.

Performance at both low and high temperatures.The acrylic acid system becomes harder and initially less viscous at low temperatures, and becomes softer and less viscous at high temperatures; Silicone systems have better temperature resistance but usually have lower initial adhesion. If the nominal peel strength is not specified with temperature, it is impossible to determine how much it still has in your actual working conditions.

05Acceptance: Make numbers comparable

A determinable adhesive specification should state at least six things: the material and surface treatment of the veneer, the thickness of the adhesive layer, whether it is peeled off at 180 ° or 90 °, the stretching speed, the static conditions after adhesion, and the temperature and humidity during testing. If one item is missing, the numbers of the two suppliers cannot be compared.

Furthermore, the value of "after aging" should be included in the clause: retest the peel strength after high temperature storage, wet heat, and temperature cycling, and specify the allowable attenuation range. The tape that peels off 1.5 N/25mm at room temperature and falls to 0.4 N/25mm at high temperature is completely qualified in room temperature testing, but it will curl on real products - this type of difference can only be screened out by aging terms.

Procurement Four QuestionsWhat surface is it pasted on and what surface treatment has it undergone? What are the compression pressure and settling time? Does it need to be cleanly peeled off after tearing? How much is allowed to drop after high temperature and humid heat? After four Q&A sessions, strong stickiness is a feasible requirement.

06By the way, strong adhesion and conductivity often cannot be achieved simultaneously

If this copper foil tape still serves as a grounding function, it will face another layer of trade-off. Conductive adhesive needs to be filled with conductive particles in the matrix, which will weaken the initial adhesion and peel strength of the adhesive; In order to improve the softness and coating amount of the adhesive layer for "strong adhesion", it will also increase the resistance in the z-direction and deteriorate the particle contact. So it is difficult for the same product to achieve extremely strong adhesion and excellent conductivity at the same time, and it is usually biased towards its main purpose.

The engineering judgment criteria are simple: is this tape primarily for structural fixation and grounding, or is it primarily for grounding and fixing? The former prioritizes peeling strength, while the latter prioritizes z-direction resistance and adds additional fixing means to the structure. Writing two things in the same specification without distinguishing priorities often results in both ends not being in place.

The difficulty of strong adhesive copper foil tape is not in "sticking", but in "sticking in the right place, in the right way, and still sticking after aging". By controlling the three variables of surface energy, compression, and time, a piece of ordinary strong adhesive tape can be used stably for many years.

For more technical information on conductive shielding materials, copper foil tapes, and flexible soft magnetic absorbing materials, please visitwww.avanzado.cn.

Contact

Contact Us

Company:Xianjin Yuan (Shenzhen) Technology Co., Ltd.

Address: 8/F, Zhongxing Building, Shajing Xinsha Road, Bao'an District, Shenzhen, Guangdong, China

Tel: 0755-22277778   13826586185

Email: duanlian@shturl.cc /xxrM

Hotline
0755-22277778
13826586185(Mr.Duan)
Wechat QRcode Wechat QRcode